Spyder

Spyder High Perf. Valve

Our new high performance or HP balanced Spyder valve has great features that sets it apart from any other valve. First, the shaft is multi-slotted. We've added a angled leading edge from the valves mouth to the exhaust port for super flow. And other features listed below. Click here for a larger view.

Our HP valve stem has slots on the sides. This provides uniform airflow and pressure on the valve stem to the valve body during firing
The HP valve stem cup seal is tapered for improved air flow and efficiency
Fully CNC machined from stainless steel with a replaceable Delrin™ valve stem cup seal
our HP valve stem has an undercut section that leads to a 30° angle which directs the air into the exhaust side of the valve during firing
The inlet port has a leading edge that is angled to further enhance airflow
Common increases average around 47fps, however its not uncommon to see 54+fps using this valve.
With such chronograph or FPS increases, the use of lower pressure springs will help reduce kick and offer less fatigue and wear on marker components
Markers with inline regulators will be able to significantly reduce the input pressure
Increases efficiency

NOTE: The addition of a low tension spring or spring kit may be necessary to achieve below 300fps operation. As a baseline, markers with inline regulators should be able to drop input pressures around 100psi from stock

Spyder High Perf. Valve Stem

Made of stainless steel with a Delrin™ cup seal this was designed with performance in mind. The shaft itself is multi-slotted for balanced air flow during valve opening. Click here for a large picture.

Our HP valve stem has slots on top and bottom. This provides uniform airflow and pressure on the valve stem to the valve body during firing
The HP valve stem cup seal is tapered for improved air flow
Fully CNC machined from stainless steel with a replaceable Delrin™ valve stem cup seal
our HP valve stem has an undercut section that leads to a 45° angle which directs the air into the exhaust side of the valve during firing
With such chronograph or FPS increases, the use of lower pressure springs will help reduce kick and offer less fatigue and wear on marker components
Increases efficiency

NOTE: The addition of a low tension spring or spring kit may be necessary to achieve below 300fps operation. Markers with inline regulators should be able to lower input pressure

Spyder EQ Bolts

This is the new bolt your hearing about, its the latest in cutting edge tech!! First, here are some benefits by using this bolt.

NO O-rings, never requires lube..
Improved consistency
Delrin bolts do not wear thebody like the stock aluminum bolt. Specific sections on the bolt are slightly smaller to decrease even more friction. Look closely...
High flow port design to stabilize the air with an ultra smooth surface finish.
The"Equalizer" chamber between the bolt and the ball is designed to displace air pressure over the whole back surface of the ball with the increased volume area and not just 6 holes.
Angled air inlet port for the best possible air flow, efficiency and less turbulence.
Our delrin bolts weigh only 28.8gr allowing faster cycling due to less inertia.
Improves accuracy by decreasing recoil while providing a quieter shot.
As pictured above, top is Top Cocking version, bottom is Side Cocking version.

Patented.

Home | Back | Next


Spyder High Perf. Valve Our new high performance or HP balanced Spyder valve has great features that sets it apart from any other valve. First, the shaft is multi-slotted. We've added a angled leading edge from the valves mouth to the exhaust port for super flow. And other features listed below. Click here for a larger view. Our HP valve stem has slots on the sides. This provides uniform airflow and pressure on the valve stem to the valve body during firing The HP valve stem cup seal is tapered for improved air flow and efficiency Fully CNC machined from stainless steel with a replaceable Delrin™ valve stem cup seal our HP valve stem has an undercut section that leads to a 30° angle which directs the air into the exhaust side of the valve during firing The inlet port has a leading edge that is angled to further enhance airflow Common increases average around 47fps, however its not uncommon to see 54+fps using this valve. With such chronograph or FPS increases, the use of lower pressure springs will help reduce kick and offer less fatigue and wear on marker components Markers with inline regulators will be able to significantly reduce the input pressure Increases efficiency NOTE: The addition of a low tension spring or spring kit may be necessary to achieve below 300fps operation. As a baseline, markers with inline regulators should be able to drop input pressures around 100psi from stock	Spyder High Perf. Valve Stem Made of stainless steel with a Delrin™ cup seal this was designed with performance in mind. The shaft itself is multi-slotted for balanced air flow during valve opening. Click here for a large picture. Our HP valve stem has slots on top and bottom. This provides uniform airflow and pressure on the valve stem to the valve body during firing The HP valve stem cup seal is tapered for improved air flow Fully CNC machined from stainless steel with a replaceable Delrin™ valve stem cup seal our HP valve stem has an undercut section that leads to a 45° angle which directs the air into the exhaust side of the valve during firing With such chronograph or FPS increases, the use of lower pressure springs will help reduce kick and offer less fatigue and wear on marker components Increases efficiency NOTE: The addition of a low tension spring or spring kit may be necessary to achieve below 300fps operation. Markers with inline regulators should be able to lower input pressure	Spyder EQ Bolts This is the new bolt your hearing about, its the latest in cutting edge tech!! First, here are some benefits by using this bolt. NO O-rings, never requires lube.. Improved consistency Delrin bolts do not wear thebody like the stock aluminum bolt. Specific sections on the bolt are slightly smaller to decrease even more friction. Look closely... High flow port design to stabilize the air with an ultra smooth surface finish. The"Equalizer" chamber between the bolt and the ball is designed to displace air pressure over the whole back surface of the ball with the increased volume area and not just 6 holes. Angled air inlet port for the best possible air flow, efficiency and less turbulence. Our delrin bolts weigh only 28.8gr allowing faster cycling due to less inertia. Improves accuracy by decreasing recoil while providing a quieter shot. As pictured above, top is Top Cocking version, bottom is Side Cocking version. Patented.
Home \| Back \| Next